CML Media and Entertainment Group - Studio

Home | About us | Contact us

Web Site

Audio
Shotgun Microphone

Applications
Commercial Audio
Pro Audio
Pro Recording

Features
Direct-coupled, balanced output ensures a clean signal even in high-output conditions.
Exclusive acoustic design* provides same directivity as mics up to 50% longer.
Switchable 150 Hz hi-pass filter.
Rugged housing made of lightweight structural-grade aluminum alloy.

Audio Technica AT4073a Line and Gradient Condenser Microphone designed for critical long-distance pickup in broadcasting, film/TV production and theater sound reinforcement applications.

The AT4073a sets new standards in small size and light weight. With an overall length of just 9.13” and weight of just 4.0 oz, the mic adds virtually no heft to the end of a fish pole or the top of a minicam. Through the use of an advanced, propriety Audio-Technica design, the interference tube of the AT4073a provides a narrow acceptance angle that would require a tube 50 percent longer using conventional technology. Audio-Technica has pioneered a unique interference tube design* in the AT4071a and AT4073a shotgun mics that provides the same directivity as mics up to 50 percent longer.

Details
Element: Externally polarized (DC bias) condenser
Polar Pattern: Line + gradient
Frequency Response: 30-20,000 Hz
Low Frequency Roll-off: 150 Hz, 12 dB/octave
Open Circuit Sensitivity: -23 dB (70.8 mV) re 1V at 1 Pa
Impendance: 100 ohms
Maximum Input Sound Level: 126 dB SPL, 1 kHz at 1% T.H.D.
Noise: 14 dB SPL
Dynamic Range (typical): 112 dB, 1 kHz at Max SPL
Signal-to-Noise Ratio: 80 dB, 1 kHz at 1 Pa
Phantom Power Requirements: 11-52V DC, 3.2 mA typical
Switch: Flat, roll-off
Weight: 4.0 oz (114 g)
Dimensions: 9.13" (232.0 mm) long, 0.83" (21.0 mm) diameter
Output Connector: Integral 3-pin XLRM-type
Accessories Furnished: AT8405a stand clamp for 5/8"-27 threaded stands; AT8134 windscreen; protective carrying case.

Boompole

This 4 section, lightweight, and cost effective boompole is made of carbon fiber in a black matte finish. The twist adjusting section locks are of a tactile coated plastic construction, and a unique reversible mounting screw adapts the boompole to the threading requirements of most microphone shockmounts with a soft rubber hand grip.

This version is lighter and offers greater extension than previous models in Gitzos' carbon fiber boompole series.

Applications

Material: Carbon Fiber

Sections: 4

Minimum Length: 32.7" (83 cm)

Maximum Length: 108.2" (274.8 cm)

Weight: 1.15 lb (521.63 gr)

Load Capacity: 4.4 lb (1.96 kg)

Hand Held Microphone

TThe M 58 has been specifically designed to satisfy the demands of electric news gathering (ENG) and electronic field production (EFP) applications.

Its sophisticated internal shockmount dramatically reduces handling noise, while the microphone's frequency response has been tailored to provide broadcasters with a very accurate and intelligible sound.

The M 58's weight-balanced design provides journalists with a high degree of comfort during lengthy interviews. Its rugged construction enables the microphone to withstand physical and environmental punishment typically encountered during field production operations. The M 58's slim profile and non-reflective Nextel® finish result in a low profile on camera.

Key Features

High output moving coil transducer

Internal shockmount reduces handling noise

Extended frequency response with rising high-end for maximum intelligibility

Rugged construction

Non-reflective Nextel® finish

Weight-balanced, slim-profile design

EIA sensitivity rating -149 dBm